Fenix WF11E ATEX lamp

Professional lamp Fenix ​​WF11E with ATEX/IEC certification for use in explosive environments. The lamp is powered by three AA batteries and provides a luminous flux of up to 200 lumens. The body of the lamp is made of antistatic plastic (polycarbonate RTP399 x 133887) with high resistance and impact resistance. In addition, the lamp is equipped with a fixed clip with an integrated magnet and a magnetic end, so it can be attached to anything iron. The lamp is mainly intended for firefighters and rescuers, and is also suitable as a work lamp for industrial establishments such as chemical plants, refineries, textile mills, paper mills, mills and other establishments with an increased risk of explosive gases and dust.

Certificates:

• Usable in zones 0-2 of explosive gases and in zones 20-22 of explosive dust.

• Full text of certificates:
  
  - IECEx: Ex ia IIC T4 Ga / Ex ia IIIC T130 ° C Yes IP66 / IP67
  
  - ATEX: II 1G Ex ia IIC T4 Ga / II 1D Ex ia IIIC T130 °C Yes IP66 / IP67

• It also meets CSA and PCEC certificates.

Parameter e ATEX lamp Fenix ​​WF11E :

• A powerful Cree XP-G2 LED with a warmer shade of light with a lifespan of 50,000 hours is used.

• Three power modes: 200 lumens (10 hours) -> 100 lumens (29.5 hours) -> 30 lumens (70 hours).

• Uses three AA batteries. Fenix ​​strongly recommends using only battery types that have been certified by the manufacturer: ENERGIZER E91, DURACELL MN1500 and RAYOVAC 815

• Protection against accidentally inserting the battery upside down (reverse polarity).

• Made of solid antistatic plastic (polycarbonate RTP399 X 133887).

• Grooving surface for better grip.

• Fixed clasp with integrated magnet.

• Magnetic end.

• Dustproof and waterproof according to the IP67 standard up to a depth of 1 meter underwater.

• Smooth aluminum reflector for a perfect light cone with an afterglow of over 185 meters (8512 cd).

• Dimensions 16.75 cm (length) x 4.9 cm (head diameter) x 2.4 cm (body width).

• Weight 160 grams (without batteries).

• The package includes three Energizer alkaline pencil batteries, which are approved for use in the lamp, a spare o-ring, a strap and a certificate valid for the EU.

To use :

The flashlight is turned on and off by holding the button on the side for 0.5 seconds. The lighting modes can be changed by short presses of the button in the order of low-medium-high.

To replace the batteries, unscrew the lamp head and remove the battery holder. When replacing the batteries, pay attention to the correct polarity marked on the holder. Put the holder back and screw the lamp head.

Warning

• Carry out all servicing and battery replacement outside of an explosive atmosphere!

• In an explosive atmosphere, use only batteries that have been certified by the manufacturer: ENERGIZER E91, DURACELL MN1500 and RAYOVAC 815

• Never mix batteries of different manufacturers, different ages or different degrees of discharge.

• For long-term storage, we recommend removing the batteries from the lamp to prevent them from leaking and damaging the lamp.

• If the protective rubber rings appear damaged after a long period of use, replace them.

• If the light flickers, does not switch to higher power modes, or does not light up, it may be for one of the following reasons:

  • Batteries are almost empty - replace them.

  • The contacts inside the lamp are clogged - clean them with a cotton swab dipped in alcohol.

  • The lamp body is loose, tighten it.

Warranty

Five-year warranty.

Max power: 200lm

Max endurance: 70 hours

Aftersight: 185m

Number of modes: 3

Weight: 160g

Power supply: 3x AA

Light source: Cree XP-G2

Waterproof: IP67 (immersion 1 m)