Mondraker Chrono 29, model 2020, black
Fork: RockShox 30 Silver TK 29, 100mm, Solo Air, tapered steerer tube, 9x135mm axle, 30mm steel stanchions, offset 46mm. Settings: 2 pos remote compression (open / lock), rebound, air preload
Head composition: Onoff Saturn tapered for 1-1 / 8 ”to 1-1 / 2” head tube, ACB sealed bearings, top 41x30.2x7x45 ° x45 °, bottom 51.9x40x8x45 ° x45 °
Stem: OnOff Sulfur, 6061 T6 Alloy, 31.8mm barbore, rise: +/- 7 °, length: sizes S / M: 60mm, size L: 80mm, size XL: 90mm
Handlebars: OnOff Sulfur 0.2, double butted 6061 alloy, rise: 4.8mm, width: 740mm, 9 ° backsweep, 0 ° upsweep, 31.8mm barbore
Grips: Onoff Twin, 1lock-on, 135 mm
Seatpost : OnOff Sulfur 0-R, 6061 T6 Alloy, 3D forged, diameter 27.2mm, length 400mm
Saddle: Mondraker XC Series Chrono R design
Front brake: Shimano MT201, RT56 160mm IS 6 bolts rotor, resin pads
Rear brake: Shimano MT201, RT56 160mm IS 6 bolts rotor, resin pads
Brake levers: Shimano MT201, tooled reach adjust
Rims: MDK-XP1 29 TLR, 25mm internal width, tubeless ready, 32 spokes
Tip: CN round stainless steel
Front hub: MDK DC20LW 9x135mm, cup & cone ball bearings, IS 6 bolts
Rear hub: MDK DHT 12x148mm, sealed bearings, IS 6 bolts
Front tire: Maxxis Ikon 29x2.20, 60TPI, Wire bead
Rear tire: Maxxis Ikon 29x2.20, 60TPI, Wire bead
Cranks: SRAM SX Eagle 12s, Boost, OAK BSA 73mm, Direct Mount chain ring, S size: 170mm, M / L / XL size: 175mm
Converters: 32T, steel, X-Sync
Middle composition: SRAM OAK BSA, sealed bearings, 73mm
Chain: SRAM SX Eagle 12s
Gearbox: SRAM SX Eagle, Type 3 roller bearing clutch, cage lock, long cage, 1x12s, X-actuation 1: 1
Gear: SRAM Trigger SX Eagle, 12s, X-Actuation 1: 1
Cassette: SRAM PG-1210 11-50 12s
Model year | 2020 |
Gears | 1x12 |
Groupset | SRAM SX |
Material | aluminium |
Brakes | Hydraulic disc brakes |
product ID | 88513 |

All bicycles at the MTBIKER shop are new, not-ridden, from an official distributor and with a full warranty. Several brands even offer a lifetime warranty on the frame after registration. We perform all warranty services in MTBIKER stores after personal delivery or after sending the bike (or its part) by courier.
- The bicycle is taken out of the manufacturer's box
- The bicycle is assembled, inspected and adjusted (front and rear derailleur, shock, fork, wheels,...)
- The bicycle is carefully packed back into a box and shipped
- If you order a bicycle for in store pick up or home delivery, the bicycle will be waiting put together, checked and ready to use for you.
- If you order a bicycle via courier to your home address, the following must be done at home:
- Take the bike out of the box and carefully remove safety material and foils
- Mount handlebar to stem (1 minute, 4 or 5 mm hex hey is needed).
- Mount front wheel to fork (1 minute, without the need of any tools if the bike has a quick release).
- Loosen the screws in the headset, straighten the stem with the front wheel, tighten the upper screw on the fork and then tighten the headset (2 minutes, 4 or 5 mm hex key is needed).
- Mount the pedals to the cranks while lubricating the thread and carefully mounting it the right way (1 minute, 8 mm hex key or 15 mm wrench).
- Mount seatpost to frame (10 seconds, without needing any tools if the frame has a quick link).
- Inflate the tyres or fork and shock to desired pressure (2 minutes, pump needed).
- Check the tightening of hex keys and quick-releases (2 minutes, 4 and 5 mm hex key is needed).
- Go for a test drive! Handle your bicycle carefully until you get used to it. If the bike has disc brakes, their performance will be limited from now on - they will gain their full power after 4-5 strong brakes at higher speed.

There are currently no reviews